When it comes to working with electrical equipment, putting safety precautions in place for any electrical project is always a top priority. From basic knowledge and equipment safety to personal precautions and equipment performance, knowing what to do to help prevent injuries and ensure safety can be a lifesaver.
Avoid Water
A critical precaution when working with electrical equipment is staying out of water. If you’re working in an area where there is a good chance you’ll be around it, wear rubber boots at all times, but avoid standing on a wet surface while working with electrical equipment. Also, when working with equipment near electrical circuits, don’t work with wet hands. Keep towels nearby so you don’t run the risk of becoming the conduit for an electric current.
Check for Live Wires
Before beginning work, check to ensure what you’re working on is not energized. Use an electrical current tester to check for live or hot wires. Check all wires and the metallic flap that covers the service panel, too. Never assume electrical devices are not energized. Check first and be safe.
Before taking a single step to service electrical equipment, disconnect the power source. It’s the only way to be 100 percent sure no current is running through the wires. For added safety, place a note on the service panel alerting others not to turn the power on.
Use the Right Fuse
When making repairs to a circuit breaker panel, be sure to use the appropriate fuse, otherwise it may result in a short circuit.
Prevent Shocks
Prevent shocks from happening by covering the bare ends of a wire in a service panel with a small plastic cap. If you touch the end by mistake, the cap works as an insulator for the copper and eliminates being shocked.
Should someone you’re working with come in direct contact with an electrical conductor, it is imperative that you not touch the person, the equipment, or the equipment cord. Shut off the power at the circuit breaker or use a leather belt to disconnect the plug from the wall.
Equipment and Personal Safety
To prevent accidents, wear rubber boots and insulated rubber gloves, shoes with insulated soles, protective garments, and safety goggles.
When working with electricity, it's best to use a wooden or fiberglass ladder versus steel or aluminum. With either an aluminum or steel ladder, should an electrical surge occur you will become one with the electric current as it passes through your body.
Non-conducting handles are a must for tools and equipment any time installation, repair, and replacement projects are in place for any type of electrical work. Always use insulated tools.
While it may be necessary to make notes or measurements during an electrical job, avoid using anything metallic such as rulers, pens, or pencils. It is also recommended not to wear any metal-based jewelry such as watchbands, chains, or rings. If you have piercings with metal studs, it would be wise to remove these as well as a safety precaution.
Dress appropriately when working with electrical equipment. This means no loose clothing that can get caught in the equipment leading to serious injury. Cold rooms can mean a buildup of condensation. When working in this type of environment, move electrical equipment away from the floor and mount on a wall or panel as a safety precaution.
Equipment Reliability A frayed cord is an accident waiting to happen. Do not use any piece of equipment that is damaged, has broken plugs, has poor insulation, or cords are coming apart. It’s in your best interest to have the equipment repaired or replaced to avoid severe injury.
Chemical effects of electric current
In 1800, a British chemist, William Nicholson showed that when electrodes were immersed in water and current was passed through water; bubbles of oxygen and hydrogen were produced. Oxygen bubbles were formed at the electrode connected to the positive terminal. Hydrogen bubbles were formed at the electrode connected to the negative terminal. When electric current is passed through a conducing solution, some chemical reaction takes place in the solution. This is called chemical effect of electric current. Some of the chemical effects of electric current are as follows:
- Bubbles of gas may be formed at electrodes.
- Deposits of metal may be seen on electrodes.
- Change of colour of solution may occur.
- WBPCS Mains Tests and Notes Program
- WBPCS Prelims Exam 2020- Test Series and Notes Program
- WBPCS Prelims and Mains Tests Series and Notes Program
- WBPCS Detailed Complete Prelims Notes